Shimpo FGV-XY-Series Instrukcja Użytkownika

Digital Force GaugeInstruction ManualPlease read the entire manual before using your gauge.FGV - 0.5/1/2/5/10/20/50/100/200 XYNIDEC-SHIMPO CORPORATION

-9-Key Operation DisplayPEAKPEAKZEROMEMMEMUNITPress UNIT to cycle through the available settings.ZEROSave the current setting, and return to the stand

-10- 4.5.4 RS-232C Baud Rate: f04This function allows you to change the RS-232C communication rate. The available baud rates are 2400, 4800, 9600, an

-11-Key OperationPOWER Turns the FGV-XY ON and OFFZERO Tares the gauge in Standard mode. Clears a peak value in Peak mode.PEAK Switches between Standa

-12-This mode shows the current force applied, tension/compression, on the sensor shaft.1. Turn on the FGV-XY by pressing POWER.2. Press ZERO to tare

-13-Key operation StatusPEAKMove to LO limit setting.MEMRegister the setting, then moveto standard measuring mode.Turn power off without any change.Ke

-14- 5.5.4 Setting LO LimitThe procedure to set the HI limit is used to set the LO limit.Section 5.5.3 contains this information.Key OperationPEAKMov

-15- Memory terms defi ned: Measurement value: The current displayed value in Standard mode. Positive maximum value (+MAX): Maximum value in the pos

-16-Key Operation DisplayTurn power off.PEAKZEROZEROMEMMEMUNIT 1. Hold down PEAK. 2. Press POWER.PEAKZEROZEROMEMMEMUNIT Release POWER. 5.6.1 Setti

-17- 5.6.2 Recording Memory DataThe following procedures explain how to activate memory recording for each memory mode. 5.6.2.1 Continuous Mode1. In

-18-Key operation DisplayTurn power off.PEAKPEAKZEROMEMUNIT1. Hold down MEM2. Press POWER PEAKPEAKZEROMEMUNIT3. Release POWERZEROD

Only use the supplied AC adapter for charging the FGV-XY. Use of a third party AC adapter will void the unit's warranty, and may cause circui

-19- 5.7.1.2 Statistics Data1. When in memory mode, UNIT will cycle through the available statistics data.2. Each press of UNIT will switch between t

-20-Key operation DisplayTurn power offPEAKPEAKZEROMEMUNIT1. Hold down MEM2. Press POWERPEAKPEAKZEROMEMUNITRelease POWERZERODeletes the current data b

-21- 5.7.2.2 Statistics Data1. When in memory mode, UNIT will cycle through the available statistics data.2. Each press of UNIT will switch between t

-22- 5.7.3 Standard Mode Memory 5.7.3.1 Accessing Memory Data1. Turn the POWER off. Press MEM and hold, then press and release POWER. Release MEM w

-23-Key operation DisplayTurn power offPEAKPEAKZEROMEMUNIT 1. Hold down MEN key 2. Press POWER key PEAKPEAKZEROMEMUNIT Release POWERM

-24- 5.8.2 Clearing All Memory1. While viewing the last memory point, press and hold ZERO.2. The display will show "nonE".3. All memory ha

-25- 6. External Data Port 6.1 Pin AssignmentPin Number Signal Name1 Analog +2 Analog GND3RxD (RS-232C Received Data)Host --> FGV4 Digital GND5 C

-26- 6.2.2 RS232C Communication CommandsTypical Host -> FGV commands."cr"means carriage return.Commands Content Response Explanation of

-27- 6.2.3 Connection between FGV and HostWithout the connection between the Digital GND and pin 5, RS-232C communication will not work. 6.3 Analog

-28- 7. Frequently Asked Questions 7.2 Technical Inquiries 7.1 ToubleshootingQuestions Cause Presumable reason ProcedureAt power on, "OVR&quo

CautionSafety PrecautionsCaution•In or around water•In direct sunlight•In high humidityKeep the AC adapter's plugs, and the FGV-XY's power j

-29- 9.Specifi cations and Dimensions 8. Support 8.1 Repair and CalibrationPlease contact your Shimpo dealer for information regarding the repair an

-30- Measurement Attachments (standard accessories)Flat Head: 12Chisel: 70°HookNotched Head: 70° Thread AdapterCone Head: 70° DimensionsThe followin

LIMITED EXPRESS WARRANTYShimpo Instruments warrants, to the original purchaser of new products only, that this product shall be free from defects i

-3-1. Product Features 42. Standard Accessory Checklist 43. Parts of your FGV-XY 5 3.1 Main Unit 5 3.2 Display 6 3.2.1

-4- 2. Standard Accessory Checklist●Before use, please confi rm that the following items are included in the carrying case.Force GaugeAC AdapterMeasur

-5- 3. Parts of your FGV-XY 3.1.Main Unit1. Sensor ShaftApply your force in line with this threaded shaft. Use the included attachments for a your

-6- 3.2 DisplayUnit TypeMeasurement ValuePeak Mode IndicatorThe default setting for the four digit display shows compression loads as a positive

-7- 4.2 Measurement AccessoriesSelect the measurement adapter for your application, and lightly hand tighten the accessory onto the sensor shaft.

-8-Key Operation DisplayTurn Power OffPEAKZEROZEROMEMMEMUNIT1. Hold down PEAK and UNIT.2. Press POWER.PEAKZEROZEROMEMMEMUNIT3. Release POWER. 4.4 Tra